boat and fittings
Roll your mouse over the picture!
Case under the beak entry
Plastic case with glassfiber strengthening.
The case slide at the lower side of the boat.
Max. loadability
27 kg.
69 000 Ft
Canvas at the water for K Maxxi and Maxxi Extra
Applicable under 7 minutes with glassfiber tent rods. The plastic elements built on the side of the boat. With holder bag. 55x65 cm
66 000 Ft
Beak covering
It can be fitted waterproof container box which can be fitted in K MAXXI with 2 winged door with rustproof hinges and lakatszem from the inside of the boat. Its top can be stepped with max. 125 kg.
61 000 Ft
Handhold for beak covering
22 mm stainless steel tube (cannot be supplemented subsequently because while building the beak
covering it is needed to build extra elements in advance)
22 000 Ft
Fisher beak covering
Large-scaled, doesn't expend out of the plane of the boot. It can be fitted on Maxxi and Maxxi Extra.
Loadability:
120 kg.
45 000 Ft
Barrier
18 mm stainless steel polished tube which can be fitted on KMaxxi and KMaxxi Extra types (on every
kind of beak coverings) subsequently too.
58 000 Ft
Beak entry
It can be fitted in K MAXXI with glue or pop rivets, its surface is extremely coarse, opened from the boat side. We can not give door to it. It covers the oblique part of the boat at front. It can be stepped with max. 120 kg, fitted with 2 pieces of plastic bika.
41 000 Ft
Mini beak entry
It can be fitted in K MAXXI with glue or pop rivets, its surface is extremely coarse, opened from the boat side. We can not give door to it.
39 000 Ft
Back plastic bench
The load capacity is maximum 120 kg. Then it can be fixed on K Maxxi and K Maxxi Extra
33 000 Ft
Little wheel corbel with windscreen frame
16 mm stainless steel brushed tube fixed with 4 pieces of transitive bolt (type 6). It can be fitted
subsequently on corbels too.
10 000 Ft
Little wheel corbel
It can be sidelong fitted, its material is fibreglass plastic, contains a little windscreen. Conforms to the lower K MAXXI sidelong height and can be used to the higher JOKER.
26 500 Ft
Big wheel to middle and sidelong
Can be fitted with screwing or sticking, laminated into the K MAXXI on the top of the seat-holder, the wheel-bowden runs through inside the seat-holder.
35 000 Ft
Standing wheel with door
Can be stuck to flat surface, can be driven on foot, wheel without steering device with windscreen and handhold tube. There is place for lot of instruments.
73 000 Ft
Jet wheel
Especially can be fitted on flat surface of dinghy, its material is fibreglass plastic, with sponge-leatherette drape. Under the drape there are little container boxes.
59 000 Ft
Plastic boat-chair with container bench
The seat is made from PVC, the holding construction is made from fibreglass plastic, the holder can be higher with 6 cm. Inside the bench you can put things through a round door. It can be ordered with rustproof rotatable construction too!
22 500 Ft, rotatable version 31 000 Ft
Chair with upholstering
It is suitable for driver and passenger chair too, with comfortable sponge- leatherette drape, with container bench, with 2 sorts of height. Sponges must be protected with canvas during containing. It can be ordered also with rustproof, rotatable construction.
27 500 Ft,rotatable version 36 500 Ft
100 litre sitting box with upholster
It is a container box which can be stuck to flat surface. Its material is fibreglass plastic, its sitting surface is upholstered with sponge- leatherette, must be protected with canvas during containing. Fitted with rustproof hinges and lock. Opening is 35x49 cm.
37 000 Ft
200 litre sitting box with upholster
Same as the 100 litre box in K MAXXI, it deems proper to fit alongside because in this way it can be passed round and sitting in the middle you can angle comfortably. The opening of the holder is 35 cm x 105 cm.
51 000 Ft
Electric motor holder
Electric motor holder from stainless steal with laminated sheet covered with fibreglass plastic, made for the size of K MAXXI.
13 000 Ft
Bathing ladder
Bathing ladder with 3 steps made for the size of K MAXXI, its material is stainless steel. It can be fitted with 4 pieces of screw (size 6).
38 000 Ft